A Custom Designed Vintage Wine Cellar
Maybe you’re a real wine enthusiast and have a large wine collection, or maybe you’re a budding collector whose been considering your very own custom wine cellar. The great thing about a custom built wine cellar is that it can be tailored it to your wine collection and your personal style. It’s also an excellent way to utilize the extra or odd space in your house.
But, where do you begin?
The purpose of a wine cellar is to properly store your wines so that they can age correctly, knowing that, it is important to properly construct your cellar. Check out the pictures below of how the Vintage Cellars custom wine cellar design team transformed an unfinished tool storage room into a cellar that fit over 2500 bottles.
|
How did we get from barren walls and a cement floor to a functioning cellar? First, we analyzed the available space. We had to keep a few practical issues in mind, such as plumbing pipes that needed access, a drain located in the cement floor that required a raised floor in case of a flood and a second door leading under the house that needed a custom manufactured exterior grade door to keep the cellar properly insulated. Additionally, we inquired about the amount of wine storage desired, and considered our client’s current wine collection, as well as wine trends, bottle sizes and varietals. This is the basic information needed to design any wine cellar. Once we had our information we were able to create a design.
With our design in hand, the next step was to prepare the room and install the cooling system. This took 7 days and required the following steps:
• Stud walls and soffit around all plumbing
• Run a cooling line or frame system
• Set cooling system evaporator coils inside wine cellar
• Set condensing unit in acceptable location
• Creating a vapor barrier
• Insulate the walls and ceiling
• Prepare the electrical and lighting
After studding the walls to frame out the wine cellar, we built a soffit to cover all the piping. Then we installed the cooling unit. We recommend using a ductless split system because it is very quiet, you control where the hot air runs and it is easily serviced. To install this system we ran a line set which runs from the ductless split location to the condenser location. We set the evaporator coils inside the wine cellar and set the condensing unit outside the house for aesthetic reasons.
Next we installed the vapor barrier. To do this, plastic sheeting was applied to the warm wall side of the cellar but was left loose around each stud cavity so they could be insulated. After the plastic sheeting you need to apply insulation to the walls and ceiling. We used rigid insulation, a hard foam with foil on the front and back. It comes in 8 x 8 foot sheets and is cut to the size of each stud cavity. We prefer rigid insulation because it has a greater insulation value per inch. Remember, the better you insulate your wine cellar, the better your cooling system runs. Since this room had a concrete floor, the floor itself did not need to be insulated and only needed an application of water based concrete sealant with low VOC. Finally, during this stage of construction we determined where the electrical outlets and ceiling lights would be placed.
The next phase of our project was focused more on design and aesthetics. Our client wanted the cellar to be constructed mostly for storage and desired minimal display with a little room for walking and a small counter to open a bottle of wine. This was all preplanned and the materials had arrived during phase one of construction. The walls, floor, racking and lighting were a simple 4-day process. Our clients choose redwood paneling for the interior walls, which we placed over the insulation. Redwood paneling is a moisture resistant product that is both practical and visually appealing.We installed the raised floor and wine racks, which were made of heart redwood to match the wall panels. We completed the wine cellar with a few display lights and the project was complete. Remember, you can transform any room or space into a wine cellar. The best part is that you get to customize it. You can keep it simple and build for volume or make it a more inviting space with personal details specific to your taste.
The possibilities are endless.
—by Jake Austad
——————————–
Editor’s Note: Different jurisdictions will have different permitting requirements and require different amounts of paperwork to be completed before a project such as this can be completed. In some areas a permit for construction can be received in a matter of hours with plans hand drawn on grid paper. In other jursdictions (such as here in Humboldt County California) it is not uncommon for a complete plot plan and very detailed, professionally prepared plans to be required before a permit to begin construction will be issued. —Michael
Powered by ScribeFire.
